Ways to relocate a baby grand piano

Pianos routinely make movers annual list of items that are most frequently damaged. Grand pianos are especially problematic. Practicing the following procedures for dismantling, cushioning and filling grand pianos will prevent damage, lower claims expense, and improve customer complete satisfaction.

1) At least 3 individuals are needed to handle a baby grand piano. If the baby grand piano requires to go up or down stairs or if a complete or performance grand piano needs to be transferred, a minimum of four people are required.

2) Always finish a comprehensive and precise stock. It may be essential or more suitable to use a visual stock to adequately explain and reveal pre-existing damage.

3) As numerous parts are taken apart, please location all hardware in an appropriately labeled parts bag and then position the parts bag in a "Parts Box".

4) Get rid of the music rack (lyre) from its track by pulling it toward the keyboard. Wrap it in a tidy furniture pad.

5) Detach the lid by getting rid of the hinge pins. Have a single person wiggle the cover, holding it opposite the hinge, while a 2nd person works the pin loose. Please be careful not to harm the wood with the pliers or with the pin itself. If necessary, cover the jaws of the pliers with a small cloth to assist avoid damage to the wood. Wrap the lid in a clean furnishings pad.

6) Eliminate the prop that holds the lid open and wrap it in a clean furniture pad. The prop has a hinge pin and is in two pieces.

7) Eliminate the pedal assembly and wrap it in a clean furniture pad. The braces at the rear of the assembly rest in slots at each end. When removing the screws, please beware not to drop the braces. In addition, please be especially cautious with the push-rods so that they will not get bent. As you deal with the piano, number the push-rods from left to right as "1", "2", and "3", by putting a piece of masking tape with the appropriate number on each rod. Note: If masking tape is not available, please usage properly identified parts bags for this purpose. When reassembling at destination, please be sure to put the rods in the proper order so that the pedals will work effectively.

8) Pad the piano by putting a tidy rolled furnishings pad (stretch-wrap the pad to prevent it from unrolling) on the cover of the keyboard to avoid it from tumbling open while you handle the piano. Note: Please guarantee that the surface area of the piano is dust-free before padding it.

9) Position a piano board and connect the straps so that it is all set to get the piano. The raised brace on the piano board should be at the keyboard end of the piano.

10) Get rid of the left here front leg by placing one individual beneath the piano at the left end of the keyboard. Be sure to have two individuals lifting the corner of the piano while the third individual eliminates the leg. Keep in mind: Please be sure to note which legs were removed from which positions given that some pianos have legs that are not interchangeable.

11) Place the piano on the piano board by decreasing the "leg-less" end onto the board. Please be sure to lift the whole piano a little while completing this maneuver to avoid excessive pressure on the remaining, attached legs this page as the piano ideas. Be sure that the piano is focused snugly versus the brace at the end of the piano board.

12) Get rid of the two remaining legs and wrap them in clean furniture pads. These legs are kept in location by a "key and slot" arrangement. To eliminate the leg, slide it inward toward the center of the piano up until it comes out of the slot.

13) Protect the piano to the piano board by bringing completions of the straps together and attaching them. Place folded burlap pads over the furnishings pads however under the straps to supply extra protection to the edges of the piano. To prevent the strap near the narrow end of the piano from slipping off, connect the loose ends of the 2 straps together.

14) To move the piano over a flat, level surface, tilt the piano and piano board and place a four-wheel dolly under the center of the piano board.

15) To move the piano up or down stairs, use the piano board as a skid. After sufficiently padding the stairs for protection versus residence damage, place the keyboard end of the piano toward the bottom of the stairs. Attach a hump strap to the top end of the piano board to prevent the piano from slipping.

16) To load the piano, leave it on the piano board and look at this web-site location it in a tier as the very first base item with the keyboard facing the wall of the preceding tier. The very best place to fill the cushioned lid is between the piano and the preceding tier or in between the wall and the piano.

Although grand pianos represent a considerable difficulty, they can be moved without damage by utilizing good sense and practicing the procedures listed above.

Leave a Reply

Your email address will not be published. Required fields are marked *